Emsworth Hampshire UK
"Glory" is a Cornish Yawl built by Cornish Crabbers in 1989 and is an excellent example of this classic design combining the advantages of modern materials with the traditional look that draws envious glances wherever she goes. Her electric lifting keel makes her ideal for exploring the harbours and creeks of the South Coast as well as being capable of longer cruises. "Glory" offers true character and traditional looks but with the low maintenance provided by a GRP hull, deck and superstructure.
Draft: 0.9 - 1.5m
GRP Hull, Deck and Superstructure (Hull Colour Oxford Blue)
Yachting Monthly described the construction as "simple but strong and neat".
Electric Lifting Iron Keel, re-galvanised in 2018
Open Aft Self Draining Cockpit
Yanmar 2GM20F 18hp Diesel Engine with Shaft Drive
Original Engine which has been well maintained - full service 2017
Freshwater Cooling System
45 Litre Steel Fuel Tank
100 Litre Flexible Water Tank
2 x Batteries (4 years old) charged by engine alternator and 30w Solar Panel
Spars and Rigging
Gaff Rigged Yawl
Wooden Spars - new main mast in 2018
Stainless Steel Standing Rigging
Running Rigging - Braid on Braid - mostly new
Slab Mainsail Reefing
Roller Headsail Reefing
Headsail, Main and Mizzen - all Tan Colour
Age unknown but described by owner as:
Headsail - Very good
Mainsail - Good
Mizzen - Acceptable
Cruising Chute - unused by current owner
Manual Bilge Pump
Automatic Bilge Pump
Nasa Duet Log (2015)
Nasa Duet Echo-sounder
Plastimo Steering Compass (illuminated)
Nasa Wind Instruments (2017)
Navigation Lights - LED - Mast and Shroud Mounted
Standard Horizon GX2000 VHF (2018)
Standard Horison CP300 Chart Plotter with CMap Cartridge (2018)
Both of the above are AIS capable with the addition of a separate AIS engine and located at the Chart Table. Plotter is visible from the Cockpit
Horseshoe Lifebuoy with vessel name and light attached
2 x Manual Fire Extinguishers (may require servicing)
Comfortable accommodation retaining traditional look and feel
Quarter Berth on Starboard Side
2 x Settee Berths
Heads Compartment with Jabsco Marine Toilet and sink (Cold Water)
Galley Area with Gas Hob, Grill and Oven
Navigation Table with Galley Sink Underneath
The Cornish Yawl was designed by Roger Dongray and 45 of these lovely craft were built at Rock in North Cornwall between 1988 and 1994 as successors to the Cornish Crabber Mark 1 and 2. GLORY is sail number 12 (CY12) and I have owned her since 2013.
When I found her she was ashore on her own yard cradle near Woodbridge and had obviously been out of the water for some time. There have been four previous owners, the original purchaser being a previous director of Barrus. He was able to import an example of the freshwater cooled 2 cylinder Yanmar (2GM20F) which he had Crabbers install in Glory. Glory Farm was the original owner’s address, which accounts for the boat’s name.
General specifications and layout are shown in the details and Glory conforms pretty well to the internal layout shown. There is a quarter berth on the starboard side, two settee berths either side of the saloon table and an optional “V-berth” at waist height forward. A Jabsco marine toilet compartment and gas cooker are to port with a navigation station and sink to starboard. With standing headroom in the after part of the cabin, the yawl makes a lovely home for a long weekend or a week’s cruising. Beaching legs allow her to take the ground.
A major part of the attraction of the yawl for me was the fact that all the controls come back into the cockpit, so even if you are new to the gaff set up it’s very simple and safe to operate. The lifting keel is operated by an electric winch which can be controlled from the cockpit. The sail plan is also very user friendly with slab reefing of the main and roller furling headsail. Glory sails nicely on mizzen and headsail alone if required.
Since acquiring Glory I’ve had the electrics pretty much renewed throughout, replaced the mast, the keel pivot bolt, the keel lifting wire, the rudder post bearing, the rudder mounting bolts, the sagging headlining, re-galvanised the lifting keel, fitted two new batteries, an ensign crane on the mizzen, serviced the automatic bilge pump, had the hull professionally copper coated, replaced all the valves and springs in the Jabsco toilet and freshwater water pump and replaced the leaky flexible water tank with a new one. Regular service items such as replacing anodes and engine oil etc have been done as necessary, the standing rigging was checked and passed in 2017 and running rigging has been replaced as needed. When the new Collars mast was installed by Nick Gates in 2018 I went with his recommendation to modify the design slightly to remove the “through mast” crosstree which was a permanent source of leaks into the timber, and fitted the mast band onto a ledge created in the mast itself. That should remove an annoying design “feature” whereby the cross tree movement makes a watertight seal almost impossible.
In 2017 I ordered a custom made boat cover which extends from mizzen up to the main mast to give some overwinter protection to the majority of the hull whether ashore or afloat.
In the electronics and navigation department I’ve fitted a Standard Horizon CP300 chart plotter and GX2000 DSC VHF. This set up will allow for future implementation of AIS on radio or plotter if required with the addition of a simple AIS engine. A NASA wind meter and Duet depth and speed log together with a Tiller Pilot auto steering system complete the electronics set up. In 2018 I installed a semi flexible 30W solar panel on the cabin roof which has kept the batteries constantly at full charge.
|Engine model:||Yanmar 2GM20F 18hp Diesel Engine with Shaft Drive|
|Length over all:||9.900m|
|Keel type:||Lifting Keel|